ST100
Installing the ST100 in a vehicle
The ST100 fits any vehicle with a 9 to 90 V DC supply. A good installation is hidden, has a clear view of the sky, uses a true ignition wire and a solid ground, and is verified before you leave.
Before you start
- Installation should be done by a technician trained on the ST100.
- Many modern vehicles use closed-loop ECU systems. Check the maker's or dealer's guidance and look for a telematics connector before cutting into wiring; a wrong connection can damage the vehicle and affect its warranty.
- Switch the ignition off and disconnect the battery terminals before wiring.
- Handle the tracker carefully: no heavy loads, water or high voltage.
Tools and materials
Tools
- Wire stripper (adjustable)
- Wire cutter
- Digital multimeter
- Screwdrivers in several sizes
- Panel tools for the dashboard: spanners, Allen keys, trim tools
- Knife
Materials
- Crimping tool, ring lugs and snap connectors
- Pliers
- Insulation tape
- Cable ties
- 2 A inline fuse and holder
- Thick double-sided foam tape
- Conduit pipe and grommets, where wires pass through panels
Where to fit it
- Good signal: The tracker sends and receives GPS and mobile signals, so pick a spot where both reach it.
- No extreme heat: Stay inside the operating temperature range. Keep away from heater outlets and hot engine parts.
- Hidden: Fit it out of sight so a thief or driver cannot find and pull it out easily.
- Little metal around it: Metal over or around the tracker weakens GPS badly.
- View of the sky: The more open sky the top of the tracker can see, the better the position.
- Away from moving parts: Do not fit it near anything that moves or vibrates heavily.
- 20 cm from control units: Keep at least 20 cm between the tracker and any ECU or control module.
- Not near heated windscreens: Windscreen heating elements can block GPS.
Good places
- Inside, beside or above the glove box
- Behind the dashboard
- On top of the dashboard, if the dashboard is not metal
Places to avoid
- Near airbags
- Under the roof lining
- Inside an AC duct
- In the engine compartment
- In the boot
- Near the fuel tank
- Near speakers
- Outside the passenger cabin
- Near radio antennas or transmitters
Which way up
- The LED side faces up, towards the sky. The GPS antenna is under that face.
- Keep metal at least 30 to 40 cm away above the tracker.
- Do not tilt it more than 50° from horizontal.
- If harsh-driving events use the accelerometer, mount it flat and square to the vehicle's length.
Power, ignition and ground
Identify each wire from the vehicle's wiring diagram or the dealer's guidance, and confirm it with a multimeter.
Power (red, +12 V / +24 V)
- Use a wire that stays live after the vehicle's electronics go to sleep, which can take 5 to 30 minutes. Measure it.
- The best source is the main supply in the fuse box.
- Fit a 2 A inline fuse on the red wire, close to the connection point.
- After connecting the tracker, measure again: the voltage must not drop.
Ignition (green)
- Use a true ignition wire: it stays live while the engine is cranking.
- Do not use an ACC (accessory) wire, which is live in the first key position and drops while cranking.
- It should stay live when other accessories are switched off.
- The ignition relay output is ideal; any relay that is live only with ignition on also works.
Ground (black)
- Connect to the chassis or a metal part fixed firmly to it.
- Crimp a ring lug on the wire and fix it with a bolt or screw.
- Scrape off paint under the lug for good contact.
Step by step
- Check the vehicle first
Test lights, wipers, horn, AC, music system and warning lamps before you start. Report any fault to the customer straight away, so it is not blamed on the tracker.
- Make it safe
Ignition off. Disconnect the battery. On vehicles with closed-loop ECU systems, check the maker's or dealer's guidance before touching wiring.
- Insert the SIM
Fit an activated Nano-SIM and check the backup battery plug (see Quick start).
- Choose the spot
Pick a hidden location with sky view and little metal, at least 20 cm from control units, LED side up.
- Find the wires
Use a multimeter only, never a test lamp. Confirm permanent +12/24 V, true ignition and a clean chassis ground.
- Connect the harness
Ground first, then power through the 2 A fuse, then ignition, then any inputs. Strip and join one wire at a time and insulate each joint before the next. Connect all wires before plugging the harness into the tracker.
- Route and secure
Run wires through existing ducts and openings, protect them with grommets or conduit where they pass edges, and tie them to fixed parts away from heat and moving parts.
- Mount the tracker
Fix it to a solid surface with thick double-sided tape and two cable ties (screws if there are mounting points), so it cannot move.
- Put the vehicle back together
Restore any factory insulation you removed, refit panels, screws and clips, and clean up.
- Test everything
Re-test all vehicle functions. Then confirm in the installer console that the tracker has a GPS fix, is sending data, reads the correct voltage and switches with the ignition.
Before leaving the vehicle, the tracker must show a GPS fix and be sending data. Run the checks in the installer console.
Good practice
- Strip wires with an adjustable stripper, not a cutter, so copper strands are not cut.
- Never push a multimeter probe into the tracker's or the vehicle's connectors; it loosens the terminals.
- Insulate every bare joint with tape, and add extra protection where wires are exposed to heat, moisture or dust.
- Do not connect to ECUs or control units directly.
- Do not run wires across floors where people step.
- Do not fix wires to parts that are removed during servicing.
- Keep the installation neat and hidden.
- If the digital output drives an immobiliser relay, wire the relay normally closed (NC) so a fault cannot stop the vehicle unexpectedly.
Troubleshooting
No LEDs at all
- Measure voltage between red and black at the harness: it must be 9 to 90 V.
- Check the 2 A fuse and the ground lug.
- If the vehicle supply is fine, the tracker may be in sleep or covert mode: switch the ignition on and wait a minute.
GSM LED stays off
- Check the SIM is activated, has data, and sits correctly in the slot.
- Check the network has coverage at the vehicle's location.
- Ask support to confirm the APN set on the tracker matches the SIM.
GSM LED blinks every second but data never connects
- The SIM is on the network but the data connection is failing: check the SIM's data plan and APN.
- Confirm with support that the server address and port are set.
GPS LED stays off
- Move the vehicle into the open; the first fix can take up to 35 seconds after a cold start.
- Check the LED side faces up and nothing metal is within 30 to 40 cm above it.
- Check the tilt is under 50°.
Ignition shows wrong
- Green must be a true ignition wire, live during cranking, not ACC.
- Measure it with the key off (0 V) and on (battery voltage).
Low voltage or power alerts
- The red wire must be a permanent supply that stays live when the vehicle sleeps.
- Check the ground lug is tight and on bare metal.
LED patterns are listed in LED indications.
Stuck on site? Email support@safartrak.com or WhatsApp +91 95988 89988 (24/7) with the IMEI and a photo of the LEDs, or contact the team.