ST100
ST100 specifications
The complete ST100 datasheet for installers and integrators. Figures are typical values from the hardware datasheet.
ST100 gps (gnss)| Item | Specification |
|---|
| Constellations | GPS, GLONASS, Galileo, BeiDou, SBAS, QZSS, DGPS |
|---|
| Receiver | 33 tracking / 99 acquisition channels |
|---|
| Tracking sensitivity | -160 dBm |
|---|
| Position accuracy | Under 5 m |
|---|
| Hot start | Under 1 s |
|---|
| Warm start | Under 25 s |
|---|
| Cold start | Under 35 s |
|---|
| Antenna | Internal |
|---|
ST100 cellular| Item | Specification |
|---|
| Network | 4G LTE and GSM/GPRS |
|---|
| GSM bands | Quad band 850 / 900 / 1800 / 1900 MHz |
|---|
| GPRS | Class B, multi-slot class 12 (up to 240 kbps) |
|---|
| SMS | Text and data |
|---|
| SIM | Nano-SIM (plastic) |
|---|
| Antenna | Internal |
|---|
ST100 power| Item | Specification |
|---|
| Input voltage | 9 to 90 V DC with overvoltage protection |
|---|
| Maximum power | 2 W |
|---|
| Backup battery | 180 mAh, 3.7 V lithium-ion |
|---|
| Current at 12 V | Data sending 90 mA · normal 60 mA · GPS sleep 10 mA · deep sleep 8 mA · online deep sleep 5 mA (averages) |
|---|
| Current at 24 V | Data sending 70 mA · normal 30 mA · GPS sleep 8 mA · deep sleep 7 mA · online deep sleep 2 mA (averages) |
|---|
ST100 inputs, outputs and interfaces| Item | Specification |
|---|
| Digital inputs | 1 (plus the ignition input) |
|---|
| Digital outputs | 1 (open drain, for an immobiliser relay) |
|---|
| Analog inputs | 1 (can be used as a digital input) |
|---|
| CAN | 1 channel |
|---|
| 1-Wire | Temperature sensor or iButton driver ID |
|---|
| Bluetooth | Internal, Bluetooth 5.0; BLE fuel sensors and other BLE accessories |
|---|
| Indicators | 2 LEDs (GPS and GSM) |
|---|
| Memory | 16 MB internal flash |
|---|
| Sensor | Accelerometer |
|---|
ST100 features| Item | Specification |
|---|
| Events | Harsh driving (eco driving), over-speeding, jamming, excessive idling, towing and crash detection, immobiliser |
|---|
| Functions | Driver behaviour, crash detection, odometer |
|---|
| Ignition detection | Ignition wire or accelerometer |
|---|
| Fuel monitoring | Analog fuel level sensor or CAN |
|---|
| Sleep modes | GPS sleep, online deep sleep, deep sleep |
|---|
| Updates and setup | Firmware over the air, configuration over USB, Bluetooth, SMS or data (GPRS) commands |
|---|
| Commands | Configuration, output control and diagnostics by SMS or data |
|---|
| Time sync | GPS, network time (NITZ), NTP |
|---|
ST100 physical and environment| Item | Specification |
|---|
| Dimensions | 83.5 × 48.5 × 13.5 mm |
|---|
| Weight | About 73 g |
|---|
| Housing | Plastic |
|---|
| Operating temperature | -25 to +85 °C (without battery) |
|---|
| Storage temperature | -40 to +85 °C (without battery) |
|---|
| Humidity | 5 to 95 %, non-condensing |
|---|
| Battery charging | 0 to +45 °C |
|---|
| Battery discharging | -20 to +60 °C |
|---|
| Battery storage | -20 to +45 °C for 1 month; -20 to +35 °C for 6 months |
|---|
Supply| Supply | Min | Typical | Max | Unit |
|---|
| Operating voltage | 9 | – | 90 | V DC |
|---|
Digital output (open drain)| Digital output (open drain) | Min | Typical | Max | Unit |
|---|
| Drain current, output off | – | – | 120 | µA |
|---|
| Drain current, output on | – | – | 0.5 | mA |
|---|
| Drain-source resistance, output on | – | – | 300 | mΩ |
|---|
Digital input| Digital input | Min | Typical | Max | Unit |
|---|
| Input resistance (DIN1) | 15 | – | – | kΩ |
|---|
| Input voltage threshold (DIN1) | 7.5 | – | – | V |
|---|
Analog input| Analog input | Min | Typical | Max | Unit |
|---|
| Input voltage, range 1 | 0 | – | 0.2 | V |
|---|
| Input resistance, range 1 | 120 | – | – | kΩ |
|---|
| Input voltage, range 2 | 0.1 | – | 32 | V |
|---|
| Input resistance, range 2 | – | 147 | – | kΩ |
|---|
CAN| CAN | Min | Typical | Max | Unit |
|---|
| Internal termination resistor | – | 120 | – | Ω |
|---|
| Differential input resistance | 19 | 30 | 52 | kΩ |
|---|
| Recessive output voltage | 2 | 2.5 | 3 | V |
|---|
| Differential output voltage | 0.5 | 0.7 | 0.9 | V |
|---|
| Common-mode input voltage | -30 | – | 30 | V |
|---|
1-Wire| 1-Wire | Min | Typical | Max | Unit |
|---|
| Supply voltage | 3 | – | 3.9 | V |
|---|
| Output inner resistance | 7 | – | – | Ω |
|---|
| Output current (above 3.0 V) | 30 | – | – | mA |
|---|
| Short-circuit current | – | 75 | – | mA |
|---|
The hardware version is printed on the label. Quote it with the IMEI when you contact support.
ST100 hardware versions| Version | Hardware code |
|---|
| Standard | TB010000 |
|---|
| With Bluetooth (BLE) | TB020000 |
|---|
| Without Bluetooth | AL030000 |
|---|
| CAN | TB040000 |
|---|
| RS485 | TB050000 |
|---|
Stuck on site? Email support@safartrak.com or WhatsApp +91 95988 89988 (24/7) with the IMEI and a photo of the LEDs, or contact the team.